Spring City, PA

Luis 4-6-26 return visit to install check valve on hydronic system, drain boiler and installed check valve, after repairs test operation and bleed air ok. all radiators getting hot, test hot water and no heat migration from hydronic piping. No charge warranty from installation

Est

Est

3/23/26 Kurt + Liz 4 AC Tuneups on 13 year old R410A Carrier Air Conditioners. Started at indoor systems, checked all electrical connections, all electrical components functioning properly. Tested return and supply temperatures, all systems have appropriate temp split. Checked static on all 4 systems/ static ok. Visually inspected coils and blower motors , all in ok condition. Poured water down drain lines to ensure there are no blockages and that there is proper drainage. Did notice no system has surge protection, informed customer of benefits of surge protection. At outdoor checked all electrical connections including total system voltage, compressor amps, and capacitors, all electrical components functioning properly on all 4 systems. Checked refrigerant levels on all systems, refrigerant levels in good range. All systems operational at time of service but past age of life expectancy.

Propane gas boiler not working properly, found error f6 showing on display. high limit issue, not enough circulation across heat exchanger. Check primary secondary circulation pump (f10 taco) found seized motor. I replaced circulation pump taco 007. I check piping and all piping starting to get hot. I did measure temperature on the return and supply. I noticed left side of the boiler by the air elimination started to get hot first and then the one on the right it was cold water coming back. This will help installers when we install new boiler, no charge for Today I talked to Joe while on site.

Completed creating estimate for new boiler and sent estimate to Greg.

Daikin mini split heat pump. Found system low on charge. Only blowing out 82 degree air temperature. Found that a flare joint at the outside unit was leaking refrigerant. Bubble checked and tightened up fitting. Added in factory charge of 2 lbs 3 ozs. And tested out mini split in heating mode. Now system is performing at a 30 degree temperature rise and refrigarant pressure is 350 psi. No charge per management. Amana heat pump system Performed heat tune up on 2023 amana heat pump system. 20x23x1 air filter is ok. Checked all electrical connections and components. Changed ecobee to permanent hold mode. Checked refrigerant pressures and temperatures. ( took photos). Heat pump is working properly at time of service. Munchkin gas boiler. Found boiler heating properly but purring like a diesel engine. Explained to Greg that this could possibly be a draft inducer motor and gas valve issue. Boiler is from 2006. Recommended replacement with a Laars boiler. Took video of noise. Also foun

Est

Fully assessed no heating situation. Mucking propane boiler which heats hard wood floors was running fine when I arrived, took photos of pipe temperatures. Did find 2023 amana heat pump locked out on code L2 high pressure lock out. . Reset heat pump and checked refrigerant pressures they were r410a 254/50 very good. Temperature rise was 17 degrees at 9 degrees outside ambient temperature very good. Heat pump systems are designed down to 15 degrees anything lower that that they will struggle to keep temp also system does not use auxiliary heat, auxiliary heat is the boiler system. Found air filter was also very dirty 20x24x1, homeowner to replace. This can definitely cause a high pressure lockout in heating mode. Heat pump is working properly again at time of service. Showed homeowner how to reset in case of extreme low temperature.

I arrived to the customers home to perform a Q.A on there new laars 95% boiler . I started with inspecting the temperature and pressure gauge. I looked at the boiler for any water leaks around the whole system. I inspected wiring connections and the neatness of the total install. I inspected the ignition system and the water drainage and made sure the condensation pump was working fine. I inspected the expansion tank and the water feeder and the circulator for proper operation. I tested for combustion to be sure it was in correct system tolerance. I checked my return and supply water temps and checked the domestic side of the boiler. The new laars boiler is in good working order.